Trang chủ Đo Lường - Kiểm Tra Máy Đo Chiều Dày Thiết bị hãng Ethern NDE

Thiết bị kiểm tra khuyết tật bằng dòng xoáy - ETher NDE Vantage Eddy Current Flaw Detector - Ethern NDE

Mã sản phẩm: ETher NDE Vantage Eddy Current |
Thương hiệu: Ethern NDE

Giá bán: Liên hệ

Thiết bị kiểm tra khuyết tật bằng dòng xoáy

Model : ETher NDE Vantage Eddy Current Flaw Detector

Maker : Ethern NDE

Yêu Cầu Giá Tốt

0984.843.683

Email: hien@ttech.vn

Thông tin sản phẩm

Thiết bị kiểm tra khuyết tật bằng dòng xoáy

Model : ETher NDE Vantage Eddy Current Flaw Detector

Maker : Ethern NDE

The ETher Vantage is a handheld, full featured Eddy Current Flaw Detector, which allows for single handed operation, leaving the operator free to use the other hand to scan with a probe. The Vantage specifications and features are comprehensive and will appeal to users in Aerospace, Offshore, Petrochemical, Power Generation and Rail / Axel Inspection industries. With a full color display and a compact and robust enclosure, the Vantageis ideal for use in on-site and factory environments.

The display screen is 320 x 240 pixels providing excellent resolution aiding accurate and rapid defect interpretation. The user interface incorporates a simple side-bar menu allowing direct access to key instrument parameters that can be instantly switched to full-screen mode. The menu system is intuitive and any experienced Eddy Current operator will quickly be comfortable with this instrument. A time-based strip chart is available to assist with faster and more reliable defect detection.

The Vantage is a true handheld Flaw Detector, weighing just 1³/₄pounds (0.8 kg) and is well balanced, allowing comfortable operation over the duration of a shift. Housed in a rugged ABS enclosure meeting IP65 splash proof requirements, the Vantage will withstand the harshest of site environments. Incorporating a Nickel Metal-Hydride Battery Pack, 6 hour battery life is typical in the standard modes and 4 hours in rotary mode.

The instrument has a single pin Lemo 00 Connector for absolute probes.

A 14 pin Connector for Rotary, Bridge and Reflection Probes.

A USB Port for connection to a PC.The USB cable and reporting software is included at no additional cost.

Features:

USB Port allows trouble free data transfer and software upgrades.
Signal-to-noise ratio is excellent, allowing greater probability of flaw detection and the Vantageperforms well with Rotating, Pencil, Weldscan and other probes.
Frequency Range is 50Hz - 12MHz and test modes can be Dual Frequency (F1 and F2) or Mix (in 4 configurations)
Three Alarm shapes are offered and can be used for F1, F2 or Mix respectively.
Data processing rate is up to 6kHz and allows storage of 200+ screen recordings of up to 40 seconds each.

Specifications:

Inspection Technology:	Eddy Current
Operating Frequencies:	60kHz, 120kHz, 240kHz, 480kHz and 960kHz
Conductivity Range:	0.5% IACS to 110% IACS, 0.28 - 64 MS/m
Accuracy:	At 68°F / 20°C. At 10% IACS: ± 0.1% IACS At 212°F / 100°C IACS: ± 0.5% IACS Over Range 0 - 104°F / 0 - 40°C: At 10% IACS ± 0.2% IACS. At 100% IACS: ± 0.8% IACS Probe in thermal equilibrium with metal
Display Resolution:	Up to 3 decimal places
Lift Off:	0.5" / 13mm probe compensated to 0.020" (0.5mm) 0.28" / 7mm probe compensated to 0.010" (0.25mm)
Temperature Measurement:	In probe sensor (accurate to 32.9°F / 0.5°C), Range 0° to 122°F / 0°C to 50°C
Automatic Temperature Compensation:	Conductivity measurements are corrected to the 68°F / 20°C value
Environmental Range:	o to 95% relative humidity,0°F to 122°F / 0°C to 50°C for reliable operation
Display:	2.8" (70mm), 320 x 240 pixels color display, LCD with selectable backlight
Construction & Storage:	High impact, splash-proof, molded UL94 - 5VA flame retardant ABS case. Protective Rubber boot to protect the unit, probes, probe cable, operator manual on USB and removable stand.
Conductivity Standards:	On top of the unit. Removable for value verification and when attached ensures thermal equilibrium.
Power:	2 x 1.5V AA NiMH Batteries, Approximately up to 6 hrs lifespan. Can also use non-rechargeable AA cells.
Size:	0.5" x 0.27" x .08" (163 x 80 x 25 mm) (L x W x D)
Weight:	0.77 lbs. (350 g.) including batteries
Data Logger Memory:	Removable 2GB micro SD Card allowing over 1 million readings to be stored.
PC Connectivity:	USB port for charger and PC communications
Probes:	0.5" / 12.7mm diameter for 60kHz to 480kHz. 0.28" / 7mm probe operates at 480kHz & 960kHz. Probes are interchangeable with simple operator resetting procedures. Probes are field exchangeable and do not require return to manufacturer for calibration.
Accessories:	Settings Reference Blocks - a range of conductivity reference standards traceable to US and European standards are available for in-field use. Up to 5 can be mounted on an aluminum anodized holding plate.