| |
DS-5654 |
DS-5652 |
DS-5634 |
DS-5632 |
DS-5624 |
DS-5622 |
DS-5614 |
DS-5612 |
| Frequency bandwidth(-3dB) |
500MHz |
350MHz |
200MHz |
100MHz |
| Rise time(Typical)） |
750ps |
1ns |
1.75ns |
3.5ns |
| Input Channel |
4 |
2 |
4 |
2 |
4 |
2 |
4 |
2 |
| Maximum Sampling Speed |
2GS/s (when 2 channels interleaved), 1GS/s (when all channels are in use) |
| Equivalent Sampling Rate |
100GS/s |
| Peak detect resolution |
1ns |
| Averaging |
2 to 65536 times (exponent of 2 step) |
| Maximum Memory Length |
5M points (when 2 channels interleaved), 2.5M points (when all channels are in use) |
| Vertical Resolution |
8-bit (When high-resolution calculation is valid: Maximum 12-bits) |
| Input voltage range |
2mV/div - 10V/div(1MΩ), 2mV/div - 2V/div(50MΩ) |
2mV/div - 10V/div(1MΩ) |
| Offset voltage |
2mV/div - 50mV/div : ±1V
50.2mV/div - 500mV/div : ±10V
502mV/div - 10V/div : ±100V |
| DC gain accuracy |
±1.5% + (0.5% of fullscale) |
| Maximum Input Voltage |
±400Vpeak CAT I (1MΩ), 5Vrms (50Ω) |
±400Vpeak CAT I (1MΩ) |
| Band-limiting filter |
Analog form : 100MHz,20MHz,2MHz,200kHz |
Analog form : 20MHz,2MHz,200kHz |
| Digital Form: Select either LPF, HPF or SMA, 4 independent channels |
| Input coupling |
GND, DC 1MΩ, AC 1MΩ,DC50Ω |
GND, DC 1MΩ, AC 1MΩ |
| Input Impedance |
1MΩ±1% //16pF、 50Ω±1% |
1MΩ±1% //20pF |
| Probe sense |
Automatic： 1：1、10：1、100：1、1000：1
Manual： 1：1、5：1、10：1、20：1、50：1、100：1、200：1、500：1、1000：1、2000：1 |
| Timebase |
500ps/div ～ 50s/div |
1ns/div ～ 50s/div |
2ns/div ～ 50s/div |
5ns/div ～ 50s/div |
| Standard probe |
SS-101R (multi-channel supplied as standard) |
SS-0130R (multi-channel supplied as standard) |
| Roll mode |
50ms/div ～ 50s/div (100kS/s max) |
| Timebase (Clock) accuracy |
±10 ppm |
| Trigger function |
| Trigger type |
Edge, Edge ALT, Edge OR, Pulse Count, Pulse Width, Cycle, Dropout, TV,
Pattern (OR, NOR, AND, NAND), Serial (UART, SPI, I2C) |
TV mode /
Line number /
Field sequence |
NTSC, PAL, Custom / Up to 3,000 / 1, 2, 4, 8 |
| Pulse Count Trigger |
1 to 9999 events |
| Pulse Width Trigger |
15ns to 50s |
| Period Trigger |
40ns to 50s |
| Dropout Trigger |
50ns to 50s |
| Pattern Trigger |
OR、NOR、AND、NAND |
Trigger source /
State /
threshhold level setting |
All Channels / HIGH, LOW, Don't Care / All Channel Independent Setting |
| Serial Trigger |
|
| UART |
Trigger Selection |
START, STOP, Parity Error, Data Pattern |
| Bit Rate |
1,000bps to 1Mbps (set in units of 100bps) |
| Comparative Data Length |
5 to 8 bits |
| Signal Source |
CH1 to CH4, EXT (CH1, CH2, EXT for 2 channel function) |
SPI
* CH1 input is reserved for SCK signal
input: Maximum 20MHz |
Trigger Selection |
Data Pattern |
| CS Selection |
Idling time specified when no positive logic/negative logic or CS |
| Comparative Data Length |
4 to 64 bits |
| Signal Source |
CH1 to CH4, EXT (CH1, CH2, EXT for 2 channel function) |
| I2C |
Trigger Selection |
START, STOP, RESTART, NACK, Data Pattern |
| Address Mode |
Selected from 7-bit / 10-bit / EEPROM read |
| Comparative Data Length |
1 to 5bytes when the address is 7-bit/10-bit, 1byte when EEPROM read (with shift comparison) |
| Signal Source |
CH1 to CH4, EXT (CH1, CH2, EXT for 2 channel function) |
| Trigger Source |
All channels, EXT (±0.5V), EXT10 (±5.0V), Line |
| Trigger Slope /Coupling |
+, - / AC, DC, High Frequency Rejection, Low Frequency Rejection, Noise Rejection |
| Display function |
| Display size/ resolution |
7.5inch color TFT-LCD with Touch screen / VGA(640*480pixels) |
| Display mode |
YT、XY、XY (Triggered) |
| Vector Display Method |
Sample Point Interpolation Display, Dot Display |
| Analog persistence mode |
Monochrome Grayscale Display, Spectrum Display |
| Persistence time setting |
100ms, 200ms, 500ms, 1s, 2s, 5s, 10s & Infinite |
| Internal Waveform Storage (REF Memory) |
5 waveforms |
| Front Panel Setting Storage |
Possible to save five settings in the internal memory, USB memory |
| PParameter Measurement, Cursor, Zoom, Calculation, Replay Functions |
| Prameter measurement |
Maximum, Minimum, Peak-Peak, RMS, Cycle RMS, Mean, Cycle Mean, Top, Base, Top-Base, +Overshoot, -Overshoot, Tr 20-80%, Tf 80- 20%, Tr 10-90%, Tf 90-10%, Freq., Period, +Pulse Count, -Pulse Count, +Pulse Width, -Pulse Width, Duty Cycle, Integral, Skew (+, -), Skew at level |
Concurrent number of measurements /
statistics display |
Four parameter maximum /Max (Maximum), Min (Minimum) ,Num (Number of the total waveforms) |
| Logging item, destination |
Time and parameter measurement results (conditions A, B, C, D),
Pass/Fail judgment results When recording: Pop-up window,
internal memory (up to 86400 entries), After recording: USB memory |
| Pass/Fail |
Judgment mode: Select between Parameter judgment and Mask judgment,
Judgment result: Save waveform (USB memory)/ Beep/ Pulse output (when equipped with DS-578 option)/ Logging,
Page search function: Select any of Fail or Pass, you can search forward or backward |
| Cursor |
Time, Amplitude, Time and Amplitude, Value at cursor |
| Zoom |
Zoom key enable display at individual grid area |
| Calculation |
Addition, Subtraction, Multiplication, FFT(8k points maximum, RECTANGULAR, HANNING, FLATTOP) |
| Rescaling / Unit conversion |
a*x+b(x: input voltage at User defined a and b) / Volt, Ampere, Watt, degree and unit-less |
| Replay |
Automatic waveform recording upto 1,024waveforms, History Replayable |
| Counter |
6-digit |
| Interface (standard) |
USB 2.0(Host&Device), LAN(100Base-TX), GPIB(Factory option: DS-576) |
| AUX Interface |
AUX connector for External options |
| Waveform Data Storage |
UUSB memory for Binary, ASCII, Mathcad, Calculation(ASCII) & Calculation(Mathcad) |
| Hardcopy Output |
Output form front panel USB port to USB memory in TIFF, BMP & PNG format or Output to PictBridge Printers |
| Calibration signal output |
Square waveform at 1kHz, 3Vp-p |
| Power / power consumption |
AC 90Vrms to 240Vrms, 47Hz to 63Hz, AC 90Vrms to 132Vrms, 380Hz to 420 Hz, 95VA max (60W max) |
| Dimensions (mm) / Weight |
Approx. 330W × 190H ×124D / Approx. 3.7kg |
| Environmental condition |
| Performance guarantee temperature |
+10℃ to + 35℃ |
Operation temperature and humidity /
Altitude conditions |
0deg. to +40˚C at 5 to 80%(RH<=30˚C) and 55%RH or less at 40˚C non-condensation /
2,000meter or lower |
| Accessory |
| Probe(multi-channel), Power cord, Front panel cover, CD-ROM(Instruction Manual, Remote Control Manual), User's Guide |
| Factory options |
AUX IO CH1/CH2 output
DS-577
(factory option) |
AUX IO1: Output of CH1 input signal with applied offset voltage, AUX IO2: Output of CH2 input signal with applied offset voltage |
AUX IO CH1/TRIG output
DS-578
(factory option) |
AUX IO1: Output of CH1 input signal with applied offset voltage,
AUX IO2: H-level pulse signal output occurs under the following conditions
・Output when triggered
・Output when Pass/Fail judgment result becomes Pass or Fail |
GPIB Interface
DS-576
(factory option) |
GPIB: IEEE488.2 (factory option) |
2 ways optional for Probe Power supply
DS-579 |
Our active probe power supply (2 systems) |