| Detection methods |
Optical reflective non-contact measurement; contact method (contact adapter supplied) |
| Measurement units |
r/min, r/s (rotations)
m/min (line speed)
ms (cycle)
COUNT (cumulative count) |
| Measurement ranges |
| |
Non-contact method |
Contact method |
| r/min (Hi range) |
6 to 99999 |
6 to 20000 |
| r/min (Lo range) |
6.0 to 600.0 |
6.0 to 600.0 |
| r/s |
0.10 to 999.99 r/s |
0.10 to 400.00 r/s |
| m/min |
0.6 to 9999.9 m/min |
0.6 to 400.0 m/min |
| COUNT |
0 to 99999 COUNT |
0 to 99999 COUNT |
| ms |
0.6 to 9999.9 ms |
2.5 to 9999.9 ms |
|
| Reflection detection distance |
20 to 300 mm |
| Display |
5-digit LED, with backlight (character height: 10.2 mm) |
| Measurement time |
Within 1 s + time required for one cycle (however, when the rotation is less than 60 r/min, twice the time required for one cycle (MAX)) |
| Display update time |
Approx. 1 s |
| Measurement accuracy |
Displayed value* x (±0.02 %) ± 1 count
* The displayed value is the count value excluding figures after the decimal point.
|
Note:
|
▉ |
The measurement accuracy of the circumferential speed depends on the number of rotations of the rotating object. |
| ▉ |
The measurement accuracy given above is for non-contact measurement. Measurement errors caused by hand shake are not included. With contact measurement, the smoothness and accuracy of the contact tip are added to the above value. |
|
| Peak hold function |
Maximum value (MAX), minimum value (MIN) |
| Memory function |
20 data (MAX) |
| Over-range function |
The over-range alarm (ERROR mark) is displayed when the measured value exceeds the display range. |
| Rotation upper limit alarm function |
The upper limit alarm ( ↑ mark) is displayed when the number of rotations exceeds the preset upper limit value. |
| Line speed calculation function |
•Calculates the line speed from the preset diameter value (mm) and the measured number of rotations
• Use the KS-100/200 circumferential rings |
| Accumulating function |
Provides a cumulative count of the input signal pulses |
| Cycle measurement function |
Measures the input pulse cycle (however, when the cycle is less than 1 s, measures the mean value of the input pulses) |
| Analog output |
Output voltage : 0 to 1 V/0 to F.S. (Full scale can be set arbitrarily.)
Conversion method : 10-bit D/A conversion
Linearity : ±1 %/F.S.
Output update time : Within 50 ms + 1 cycle
Temperature stability : ±0.05%/FS/°C (span & zero)
Setting error : ±0.5 %/F.S.
Load resistance : At least 100 kΩ |
| Pulse output |
Output voltage : Hi level = At least +4.5 V, Lo level = Up to +0.5 V
Output logic : Positive logic
Load resistance : At least 100 kΩ |
| Operating temperature |
0 to 40 °C |
| Storage temperature |
-10 to 50 °C |
| Power source |
Four AAA alkaline batteries or exclusive AC adapter (PB-7090 option) |
| Battery life |
At least 32 hours (when the backlight is OFF)
At least 8 hours (when the backlight is ON) |
| Low battery alarm indicator |
A low battery alarm mark (LOW) is displayed when the battery voltage falls below 4.4 V. |
| Outer dimensions |
180.5 (W) X 47.5 (H) X 66 (D) mm
237.2 (W) X 47.5 (H) X 66 (D) mm (with the contact adapter) |
| Weight (including batteries) |
Approx. 267 g
Approx. 329 g (with the contact adapter) |
| Accessories |
Contact adapter (HT-0502) 1
Contact tip for rotation measurement (KS-300) 1
Circumferential ring (KS-200) 1
Reflective marks (12-mm square; 25 pcs.) 1 sheet
AAA alkaline batteries 4
Carrying case 1 |
Peripherals
(sold separately) |
AX-501 Signal output cable (2-m length) (used for both analog and pulse outputs) ø2.5 pin plug—CO2 (BNC) plug
HT-0522 Magnetic stand + HT-0521A Stand jig
LA-0203A Measurement tripod (Used in combination)
PB-7090 AC adapter (100 to 240 VAC)
HT-0502 Contact adapter
KS-100 Circumferential ring (mm/s)
KS-200 Circumferential ring (m/min)
KS-300 Contact tip (for rotation measurement)
KS-700 Extension shaft for KS-300
HT-011 Reflective marks (10 sheets/pack)
|