Trang chủ Đo Lường - Kiểm Tra Đo lường và hiệu chuẩn tần số, vô tuyến điện tử Thiết bị hãng Marvin Test

PXI Stimuli Instrumentation GX1110 Marvin Test

Mã sản phẩm: GX1110 |
Thương hiệu: Marvin Test

Giá bán: Liên hệ

PXI Stimuli Instrumentation
Model: GX1110
Hãng: Marvin Test

Yêu Cầu Giá Tốt

0984.843.683

Email: hien@ttech.vn

Thông tin sản phẩm

Triggering
The GX1110 series provides an external trigger input, offering users the ability to control waveform generation via external trigger events. When operating in the AWG mode, waveform trigger modes include continuous, triggered, gated hold, and burst functionality.

Sample Clock
The GX1110 Series utilizes a PLL, providing a programmable sample clock for the AWG mode of operation. The reference clock is provided by an on-board crystal oscillator, or alternately, an external 10 MHz reference can be used. When operating in the DDS mode, an on-board crystal oscillator source provides a 100 MHz clock source for the DDS generator and associated D to A converter.

Thông số kỹ thuật

STANDARD WAVEFORMS
Sine, triangle, square, pulse, ramp up, ramp down, sinc (sine(x) / x), Guassian pulse, noise
Maximum Frequency (FS = 100 MHz)	WAVEFORM	DDS MODE	AWG MODE
	Sine	30 MHz	6.25 MHz
	Triangle	1 MHz	6.25 MHz
	Ramp	1 MHz	6.25 MHz
	Pulse		6.25 MHz
	Square	30 MHz	50 MHz
	Noise		1 MHz
	Gaussian pulse		1 MHz
	Sin(x) / x		1 MHz

ARBITRARY WAVEFORM GENERATOR MODE
Sample Rate	10 mS/s to 100 MS/s
Sample Rate Resolution and Accuracy	4 digits or 0.01 Hz, which ever is lower 0.01% accuracy
Vertical Resolution	12 bits
Waveform Memory	2 M samples
DDS MODE
Frequency Range, Resolution, and Accuracy	10 µHz to 30 MHz 10 µHz, resolution 50 ppm accuracy (OCXO option available for higher accuracy)
Non-Harmonic Spurious Components	< 60 dBc (DC to 1 MHz)
Distortion (2nd Harmonic Relative to Carrier)	< -60 dBc @ < 200 kHz < -35 dBc @ < 2.0 MHz < -20 dBc @ < 20 MHz
Modulation	AM: Int. / Ext. 0 - 100%, DC to 20 kHz FM: Int. / Ext. DC to 20 kHz Phase offset: 0 - 360 degrees, 0.1 degree resolution
MAIN OUTPUT
Connector	Front panel BNC
Output Mode	On / Off
Output Impedance	50 Ω, ±1%
Protection	Protected against shorts to ground and over-voltage
Amplitude Range	100 mV_PP to 8 V_PP into 50 Ω; double into open circuit. 0.1, 0.3, 1, 3, and 8 V_PP, FS ranges.
Amplitude Resolution	3 digits
Amplitude Accuracy	±(2% of programmed value + 5 mV) < 1 V ±(1% of programmed value + 10 mV) ≥ 1 V
Offset Range	0 to ±5 V, amplitude dependent
Offset Resolution	3 digits
Offset Accuracy	±(1% of programmed value + 20 mV)
Rise Time	< 15 ns into a 50 Ω load (10% to 90% full scale step)
Abberations	< 5% of p-p amplitude, ±50 mV
Flatness	±.5 dB to 10 MHz, ±1 dB to 30 MHz
Filters	30 MHz, elliptical; DDS mode 30 MHz, bessel; AWG mode
SYNC OUTPUT
Connector	Front panel BNC output is synchronous with output waveform
Impedance	50 Ω, ±1%
Level	TTL compatible
MARKER OUTPUT
Positive pulse, user programmable and synchronous with the waveform output.
Connector	Front panel PS2
Impedance	50 Ω, ±1%
Level	TTL compatible

TRIGGER MODES
Continuous	Output continuously generated
Triggered	Output waveform triggered by external or software triggered event. The external trigger signal edge may be a rising or falling edge.
Start / Stop	Output waveform triggered by a trigger signal edge. Waveform is continuously generated until the occurrence of an another trigger edge. The trigger signal may be external or software generated. The external trigger signal edge may be the rising or falling edges.
Gated	Same as Triggered mode except that the waveform is generated for as long as the gate signal stays true (logic one). When the gate signal goes false (logic zero) the output goes quiescent.
Gated Hold	Same as Gated mode except that when the gate signal goes true (logic high) the waveform freezes until the gate signal goes low.
Burst	Output waveform will become active on the occurrence of a trigger edge. The selected waveform is generated for a preset number of cycles between 2 and 1,048,576. Output will then disable.
EXTERNAL TRIGGER INPUT
Connector	Front panel PS2
Impedance	10 K Ω nominal
Threshold Level	TTL
Repetition Rate	DC to 10 MHz
Minimum Pulse Width	50 ns
Slope	Positive or negative going edge
EXTERNAL INPUT / OUTPUT CLOCK
Connector	Front panel BNC
Input Impedance	10 K Ω nominal
Threshold Level	TTL
Output Impedance	50 Ω
EXTERNAL MODULATION INPUT
Connector	Front panel PS2
Input Voltage Range	5 V_PP for 100% modulation (AM & FM)
Input Impedance	10 K Ω nominal
Bandwidth	DC to 20 kHz

GENERAL
Power Requirements	15 W (max)
Current Consumption (Maximum)	+5 V @ 1 A +12 V @ 300 mA -12 V @ 300 mA +3.3 V @ 1 A
Weight	Approx. 12 oz
Size	3U, single slot
Operating Temperature	0 °C to +50 °C
Storage Temperature	-20 °C to +70 °C
Humidity (Non-Condensing)	5% to 95%, < 70 °C
Safety	Designed to meet IEC 1010-1, UL 3111-1, and CSA 22.2#1010
CE Labeled	Yes
Calibration Interval	1 year